VXB Ball Bearings

 





  Home > Metric Bearings > 25mm inner diameter Bearings >

6305NR Nachi Bearing Open Snap Ring Japan 25x62x17
6305NR Nachi Bearing Open Snap Ring Japan 25x62x17


 
Our Price: $15.49
. Item: 6305NR Nachi Ball Bearing
. Type: Nachi Deep groove Ball Bearing
. Dimensions: 25mm x 62mm x 17mm/Metric
. ID (inner diameter)/Bore: 25mm
. OD (outer diameter): 62mm

Stock Status:In Stock
Product Code: KIT9950
Qty:

Description
 
6305NR Nachi Bearing
With Snap Ring (C clip)
Made in Japan


"6305NR
"6305NR

6305NR Nachi Bearing with a Snap Ring, the 6305NR inner diameter is 25mm, the 6305NR outer diameter is 62mm and the 6305NR width is 17mm.

  • Item: 6305NR Nachi Ball Bearing
  • Type: Nachi Deep groove Ball Bearing
  • Dimensions: 25mm x 62mm x 17mm/Metric
  • ID (inner diameter)/Bore: 25mm
  • OD (outer diameter): 62mm
  • Width/Height/thickness: 17mm
  • Size: 25 x 62 x 17 mm
  • Quantity: One Bearing
  • Dynamic load rating Cr: 23,600 N
  • Static load rating Cor: 12,100 N
  • Limiting Speed:
    • Grease Lubrication: 12,000 RPM
    • Oil Lubrication: 14,000 RPM
  • Made in Japan

Nachi Deep Groove Ball Bearings

Deep Groove ball bearings are the most popular of all the ball bearing types because they are available in a widevariety of seal, shield and snap-ring arrangements. The bearing ring grooves are circular arcs made slightly larger than the radius of the ball. The balls make pointcontact with the raceways (elliptical contact when loaded). The inner ring shoulders are of equal height (as theouter ring shoulders). Deep Groove ball bearings can sustain radial, axial, or composite loads and because of simple design, thisbearing type can be produced to provide both high-running accuracy and high-speed operation. Deep Groove ball bearings having an outside diameter less than 9 mm are known as Miniature ball bearings. Deep Groove ball bearings having an outside diameter => 9 mm and a bore diameter < 10 mm are known asExtra-small ball bearings. Standard ball retainers (cages) are made from pressed steel. Machined cages are used in bearing operating atvery high speed or for large diameter bearings. Deep groove ball bearings with seals or shields are standardized. They contain proper amount of grease inadvance.

Kit9950


Average Rating: 5 of 5 Total Reviews: 5 Write a review »

  0 of 0 people found the following review helpful:
 
snap ring bearing July 18, 2016
Reviewer: Gary from Derry, PA United States  
Excellent service, quick shipping and a great price

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
RD400 (OUTER) crank bearing replacement November 21, 2012
Reviewer: GSXRDman from WA state  
Great bearing.  my machinist (RB Designs  oregon) cuts the circlips that come w/ these bearings and uses o-rings in their place (hold bearing).  The O.E.M. 1/2 circlip is used on the primary gear / clutch basket side.  I do long 4 our rides (like a 4 stroke). <---so make sure you cut off ALL circlips and then fit o-rings.  You do this because there is no locating pins (like o.e.m.)  but these haven't been sitting on a shelf for 36 years either.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Perfect Stock Replacement November 3, 2011
Reviewer: Don from Boston, Ma  
Stock Yamaha RD350 250 crank bearing

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
perfect for me January 18, 2011
Reviewer: Rabalder from Norway  
gearbox on a Kawasaki

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Exact fit do a little research on HTF October 26, 2010
Reviewer: Mike's tractor from Prince George VA  
I had to do a alot of research to find out exactly which bearings fit my Ford tractor. In the end I saved well over 80% cross-referencing the VXB bearings to the ford numbers. The inside  outside and width measurements helped the most.

Was this review helpful to you?