VXB Ball Bearings

 





  Home > Metric Bearings > 12mm inner diameter Bearings >

  6001 Nachi Bearing Open C3 Japan 12x28x8
6001 Nachi Bearing Open C3 Japan 12x28x8
6001 Nachi Bearing Open C3 Japan 12x28x8


 
Our Price: $6.88
. Item: 6001 Nachi Ball Bearing
. Type: Nachi Deep groove Ball Bearing
. Radial Clearance: C3
. Dimensions: 12mm x 28mm x 8mm/Metric
. ID (inner diameter)/Bore: 12mm

Stock Status:In Stock
Product Code: KIT9803
Qty:

Description
 
6001 Nachi Bearing
12mm x 28mm x 8mm
Made in Japan



6001 Nachi Bearing, Made in Japan, the 6001 inner diameter is 12mm, the 6001 outer diameter is 28mm, the 6001 width is 8mm.

  • Item: 6001 Nachi Ball Bearing
  • Type: Nachi Deep groove Ball Bearing
  • Radial Clearance: C3
  • Dimensions: 12mm x 28mm x 8mm/Metric
  • ID (inner diameter)/Bore: 12mm
  • OD (outer diameter): 28mm
  • Width/Height/thickness: 8mm
  • Size: 12 x 28 x 8 mm
  • Quantity: One Bearing
  • Dynamic load rating Cr: 5,100 N
  • Static load rating Cor: 2,390 N
  • Limiting Speed:
    • Grease Lubrication: 28,000 RPM
    • Oil Lubrication: 32,000 RPM
  • Made in Japan

Nachi Deep Groove Ball Bearings

Deep Groove ball bearings are the most popular of all the ball bearing types because they are available in a widevariety of seal, shield and snap-ring arrangements. The bearing ring grooves are circular arcs made slightly larger than the radius of the ball. The balls make pointcontact with the raceways (elliptical contact when loaded). The inner ring shoulders are of equal height (as theouter ring shoulders). Deep Groove ball bearings can sustain radial, axial, or composite loads and because of simple design, thisbearing type can be produced to provide both high-running accuracy and high-speed operation. Deep Groove ball bearings having an outside diameter less than 9 mm are known as Miniature ball bearings. Deep Groove ball bearings having an outside diameter => 9 mm and a bore diameter < 10 mm are known asExtra-small ball bearings. Standard ball retainers (cages) are made from pressed steel. Machined cages are used in bearing operating atvery high speed or for large diameter bearings. Deep groove ball bearings with seals or shields are standardized. They contain proper amount of grease inadvance.

Kit9803


Average Rating: 5 of 5 Total Reviews: 4 Write a review »

  0 of 0 people found the following review helpful:
 
Good quality we recommend it December 23, 2014
Reviewer: RJ from Cleveland Ohio  
worked well for our tool grinder

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Best case bearing for 2 cycle motors August 5, 2012
Reviewer: Bbbutch  
I build and rebuild small 2 stroke motors. The 6001 Nachi open bearing is the best for replacing the stock lower case crank bearings. I've been using them for over 4 years on 7 different motors that I race large scale RC off road with and they have never failed once.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Best bearings for rebuilding small motor October 26, 2010
Reviewer: BBButch from Redding, CA.  
These are the top of the line bearings to rebuild the lower case of Zenoah and CY motors.  I've used more expensive bearings that did not last as long as the Nachi bearigs. Now that I have experienced these bearings I will never go back.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Great bearings at a great price. October 26, 2010
Reviewer: Mike from Phoenix AZ  
RC car engine

Was this review helpful to you?