VXB Ball Bearings

 





  Home > Mounted Bearings >

1" Bearing UCP205-16 + Pillow Block Cast Housing Mounted Bearings
1" Bearing UCP205-16 + Pillow Block Cast Housing Mounted Bearings


 
Our Price: $9.37
. Item: UCP205-16 Bearing
. Type: Pillow Block Mounted Bearing
. Bolt Size: 3/8" inch
. Basic Dynamic Load (Cr): 14 KN
. Basic Static Load (Cor): 7.85 KN

Stock Status:In Stock
Product Code: KIT920
Qty:

Description
 
UCP205-16 Pillow Block Bearing
Set Screw Type High-Center Height
1" inch Inner Diameter


1" inch UCP205-16 Pillow Block Bearing:vxb:Ball Bearing
1" inch UCP205-16 Pillow Block Bearing:vxb:Ball Bearing
1" inch UCP205-16 Pillow Block Bearing:vxb:Ball Bearing

UCP205-16 Pillow Block Bearing, UCP205-16 is Set Screw Type High-Center Height, Inner Diameter is 1" inch

  • Item: UCP205-16 Bearing
  • Type: Pillow Block Mounted Bearing
  • Bolt Size: 3/8" inch
  • Basic Dynamic Load (Cr): 14 KN
  • Basic Static Load (Cor): 7.85 KN
  • Bearing No: UC205-16
  • Housing No: P205
  • Quantity: One Bearing


Dimensions (Inches)
h a e b S2 S1 g W B1 n
1-7/16" 5-1/2" 4-1/8" 1-1/2" 3/4" 1/2" 1/2" 2-25/32 1.339" 0.563"



1" Bearing UCP205-16 + Pillow Block Cast Housing Mounted Bearings

kit920


Average Rating: 4.5 of 5 Total Reviews: 11 Write a review »

  0 of 0 people found the following review helpful:
 
Very good bearings September 12, 2015
Reviewer: bisonhill from Martinez, CA  
To be installed in replacement for main bearings on Kemp chipper/shredder, the casting had to be modified some, but the functionality is excellent.  There didn't seem to be any duct leading from the grease zerk to the bearing..??

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Working well beyond intended use. April 29, 2013
Reviewer: Roger from Baysde, CA  
I have four of the UPC205-16 bearings (two on each end)on a 1500 pound home made roller for compacting subsoil and gravel in a roadway. I am sure they were not intended for this use and I was concerned that they would be the weak link in the design. However  so far they have held up under considrable loads and vibration. I did have to add shims under the center of the bearings because they were not solid across the bottom as they had been in the same bearings I purchased in the past. Under normal circumstances these bearings can not be beat for the price.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
feels good February 12, 2013
Reviewer: Jimmy D from Limerick PA  
I have not used them yet.  I played with them in my hand  turing the ring to see how stiff.  I plan to buy more if it works with my project. I don't anticipate any problems.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
I would buy this product again December 30, 2012
Reviewer: John the Builder from Sydney, Australia  
The product is useful for use in the workshop for various applications for example driving a belt pulley.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Super service and fast handling May 12, 2012
Reviewer: handyman from Norway  
Super service and fast handling

Was this review helpful to you?

View All Customer Reviews